Scott Wilkinson
Sort By: Post Date | Title | Publish Date
Ask Home Theater
Scott Wilkinson May 23, 2012 0 comments
Because you are a home-theater Jedi, my question may seem a bit primitive. However, I am compelled to ask only because my own A/V guy can only seem to give me answers in terms of bass curves and decibels. Which processing mode is better to use, Dolby Digital or THX?

I am using an Integra DTR-7.9 A/V receiver with Anthony Gallo A'Diva Ti speakers for the front left, right, and center, three Gallo Micro Nucleus Ti speakers for the surrounds, and a Gallo MPS-150 sub modified by Gallo with its upgraded TR-3 driver for a 6.1 setup. My receiver automatically switches to Dolby Digital EX or THX Surround EX (whichever I choose) when I play 5.1 or better content, but which one should I have it switch to?

Where THX is concerned, I know that all speakers should have a frequency response down to at least 80Hz, which only three of mine do—the A'Diva Ti speakers (the Nucleus Micro Ti speakers only go down to 90Hz). I fear you may tell me to just set it to whichever sounds better, but a guy like me needs more than that. With my setup, what would you do? I like the brightness of Dolby Digital, but I also like the punch of THX, though the highs seem muddled because of Re-EQ (which I can turn off). Should I turn on Loudness Plus and ditch Dynamic EQ? Lots of questions, too many settings, I need guidance!

"Help me Obi-Scott Kenobi, you're my only hope."

Adam Meyerson

Ask Home Theater
Scott Wilkinson May 22, 2012 0 comments
Andrew Jones, chief speaker engineer for Pioneer and TAD Labs, talks about his illustrious career as a speaker designer with KEF and Infinity, the difference between research and product development, the importance of knowing what and how to measure audio performance, how he was able to design Pioneer's entry-level speakers to perform so well, his work with ultra-high-end speakers at TAD Labs, answers to chat-room questions, and more.

Run Time: 1:08:37

Ask Home Theater
Scott Wilkinson May 21, 2012 0 comments
I purchased a Sony VPL-HS20 in 2003, and I have enjoyed the picture quality until recently, when the projector started intermittently turning off without notice. I figure it's time for a new projector, although I can no longer afford one in the $3000 range. I live in Canada, and the Epson PowerLite Home Cinema 8345 (similar to the 8350) is around $1250. Also, if I wanted 3D (not urgent), the Epson 3010 is around $1400 on Amazon.

I currently project onto a 119-inch screen with some light control, although it is not perfect during the day. If I purchased a budget projector such as one of the Epsons mentioned above, will the quality be at least as good as what I've seen from my Sony? If not, can you recommend something else for me?

Paul Barnick

Ask Home Theater
Scott Wilkinson May 16, 2012 12 comments
I've heard you say, "Make sure your surround speakers are the same brand as the fronts." I have Hsu Research speakers for the front left, right, and center, Axiom dipole surrounds, and a JBL 12-inch subwoofer. I've been told by lots of audio geeks that I don't need to match the surrounds to the fronts. But after I heard what you said, I got confused. Help!

Mark Hudson

Scott Wilkinson May 15, 2012 0 comments
Juergen Herre, chief scientist at Fraunhofer Institute for Integrated Circuits and professor at Erlangen University in Germany, discusses the development of the MP3 audio format (technically called MPEG-1 Layer 3), how lossy audio codecs work using psychoacoustics, how higher bitrates yield higher audio quality, constant versus variable bitrates, more recent audio codecs such as MPEG-2 AAC and surround MP3, 3D audio, object-oriented audio, answers to chat-room questions, and more.

Run Time: 1:02:14

Ask Home Theater
Scott Wilkinson May 14, 2012 13 comments
I would like to buy a TV with a 65-inch or larger screen. My budget is $3000 to $4000. Unfortunately, the room it will be in is very bright with a 15-foot floor-to-ceiling glass window behind the set facing east. I watch a few DVDs, but mostly just cable TV in HD when available; 3D is not important to me. Obviously, I am concerned about light reflection off the screen. What do you suggest?

Orrin

Ask Home Theater
Scott Wilkinson May 10, 2012 6 comments
I just bought a Mitsubishi WD-Y657 65-inch DLP rear-projection TV in perfect condition for $300. I've tried to find the best picture settings online, but I can't find anything for this model. Can you provide any help or suggest a good setup disc? Hopefully something easy to use, as I'm fairly new at this.

Cody Lacroix

Scott Wilkinson May 08, 2012 0 comments
Boxee co-founder and CEO Avner Ronen talks about the new paradigm of online video delivery, image and sound quality versus bandwidth, integrating and unifying various online sources, the importance of the user interface, the trend toward encrypting basic cable channels, the founding and evolution of Boxee, the Boxee box and remote, online delivery of 3D and 4K, answers to chat-room questions, and more.

Run Time: 1:00:21

Ask Home Theater
Scott Wilkinson May 07, 2012 11 comments
My Pioneer VSX-35TX A/V receiver just died. I'm looking for a new receiver in the $500 range, but I'm having a hard time finding any that have, among other things, a digital-audio output. Why is that important? I have a Pioneer TRE-D800 wireless headphone transmitter that does 5.1 audio, and it can accept either optical or coaxial inputs. Another consideration is that my Pioneer Elite PRO-510HD RPTV has no HDMI inputs, so I need a component-video output. I want a receiver that can grow from here, so 3D pass-through is a must, and 7.1 audio would be a bonus.

I'm interested in the Pioneer VSX-1122, but it doesn't seem to have all the outputs I need. The Pioneer Elite VSX-52 has exactly what I'm looking for, but it's $400 out of my range. What other brands of receivers should I be looking at, or am I just plain screwed at my current budget?

Chris Friebus

Ask Home Theater
Scott Wilkinson May 04, 2012 6 comments
I have a 140-inch, 2.35:1 screen, and I'd like to replace my existing projector with a 3D model. I've narrowed my choices to the Epson PowerLite Pro Cinema 6010 and the JVC DLA-X30. What do you think?

Kamarul Ariffin

Site Map / Direct Links